linux/drivers, branch v3.0.57

xhci: Extend Fresco Logic MSI quirk.

2012-12-17T18:49:05Z

commit bba18e33f25072ebf70fd8f7f0cdbf8cdb59a746 upstream. Ali reports that plugging a device into the Fresco Logic xHCI host with PCI device ID 1400 produces an IRQ error: do_IRQ: 3.176 No irq handler for vector (irq -1) Other early Fresco Logic host revisions don't support MSI, even though their PCI config space claims they do. Extend the quirk to disabling MSI to this chipset revision. Also enable the short transfer quirk, since it's likely this revision also has that quirk, and it should be harmless to enable. 04:00.0 0c03: 1b73:1400 (rev 01) (prog-if 30 [XHCI]) Subsystem: 1d5c:1000 Physical Slot: 3 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Reported-by: A Sh Tested-by: A Sh Signed-off-by: Greg Kroah-Hartman

USB: OHCI: workaround for hardware bug: retired TDs not added to the Done Queue

2012-12-17T18:49:04Z

commit 50ce5c0683aa83eb161624ea89daa5a9eee0c2ce upstream. This patch (as1636) is a partial workaround for a hardware bug affecting OHCI controllers by NVIDIA at least, maybe others too. When the controller retires a Transfer Descriptor, it is supposed to add the TD onto the Done Queue. But sometimes this doesn't happen, with the result that ohci-hcd never realizes the corresponding transfer has finished. Symptoms can vary; a typical result is that USB audio stops working after a while. The patch works around the problem by recognizing that TDs are always processed in order. Therefore, if a later TD is found on the Done Queue than all the earlier TDs for the same endpoint must be finished as well. Unfortunately this won't solve the problem in cases where the missing TD is the last one in the endpoint's queue. A complete fix would require a signficant amount of change to the driver. Signed-off-by: Alan Stern Tested-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman

ACPI / video: ignore BIOS initial backlight value for HP Folio 13-2000

2012-12-17T18:49:04Z

commit 129ff8f8d58297b04f47b5d6fad81aa2d08404e1 upstream. Or else the laptop will boot with a dimmed screen. References: https://bugzilla.kernel.org/show_bug.cgi?id=51141 Tested-by: Stefan Nagy Signed-off-by: Zhang Rui Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

ACPI / PNP: Do not crash due to stale pointer use during system resume

2012-12-17T18:49:04Z

commit a6b5e88c0e42093b9057856f35770966c8c591e3 upstream. During resume from system suspend the 'data' field of struct pnp_dev in pnpacpi_set_resources() may be a stale pointer, due to removal of the associated ACPI device node object in the previous suspend-resume cycle. This happens, for example, if a dockable machine is booted in the docking station and then suspended and resumed and suspended again. If that happens, pnpacpi_build_resource_template() called from pnpacpi_set_resources() attempts to use that pointer and crashes. However, pnpacpi_set_resources() actually checks the device's ACPI handle, attempts to find the ACPI device node object attached to it and returns an error code if that fails, so in fact it knows what the correct value of dev->data should be. Use this observation to update dev->data with the correct value if necessary and dump a call trace if that's the case (once). We still need to fix the root cause of this issue, but preventing systems from crashing because of it is an improvement too. Reported-and-tested-by: Zdenek Kabelac References: https://bugzilla.kernel.org/show_bug.cgi?id=51071 Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

ACPI / battery: Correct battery capacity values on Thinkpads

2012-12-17T18:49:04Z

commit 4000e626156935dfb626321ce09cae2c833eabbb upstream. Add a quirk to correctly report battery capacity on 2010 and 2011 Lenovo Thinkpad models. The affected models that I tested (x201, t410, t410s, and x220) exhibit a problem where, when battery capacity reporting unit is mAh, the values being reported are wrong. Pre-2010 and 2012 models appear to always report in mWh and are thus unaffected. Also, in mid-2012 Lenovo issued a BIOS update for the 2011 models that fixes the issue (tested on x220 with a post-1.29 BIOS). No such update is available for the 2010 models, so those still need this patch. Problem description: for some reason, the affected Thinkpads switch the reporting unit between mAh and mWh; generally, mAh is used when a laptop is plugged in and mWh when it's unplugged, although a suspend/resume or rmmod/modprobe is needed for the switch to take effect. The values reported in mAh are *always* wrong. This does not appear to be a kernel regression; I believe that the values were never reported correctly. I tested back to kernel 2.6.34, with multiple machines and BIOS versions. Simply plugging a laptop into mains before turning it on is enough to reproduce the problem. Here's a sample /proc/acpi/battery/BAT0/info from Thinkpad x220 (before a BIOS update) with a 4-cell battery: present: yes design capacity: 2886 mAh last full capacity: 2909 mAh battery technology: rechargeable design voltage: 14800 mV design capacity warning: 145 mAh design capacity low: 13 mAh cycle count: 0 capacity granularity 1: 1 mAh capacity granularity 2: 1 mAh model number: 42T4899 serial number: 21064 battery type: LION OEM info: SANYO Once the laptop switches the unit to mWh (unplug from mains, suspend, resume), the output changes to: present: yes design capacity: 28860 mWh last full capacity: 29090 mWh battery technology: rechargeable design voltage: 14800 mV design capacity warning: 1454 mWh design capacity low: 200 mWh cycle count: 0 capacity granularity 1: 1 mWh capacity granularity 2: 1 mWh model number: 42T4899 serial number: 21064 battery type: LION OEM info: SANYO Can you see how the values for "design capacity", etc., differ by a factor of 10 instead of 14.8 (the design voltage of this battery)? On the battery itself it says: 14.8V, 1.95Ah, 29Wh, so clearly the values reported in mWh are correct and the ones in mAh are not. My guess is that this problem has been around ever since those machines were released, but because the most common Thinkpad batteries are rated at 10.8V, the error (8%) is small enough that it simply hasn't been noticed or at least nobody could be bothered to look into it. My patch works around the problem by adjusting the incorrectly reported mAh values by "10000 / design_voltage". The patch also has code to figure out if it should be activated or not. It only activates on Lenovo Thinkpads, only when the unit is mAh, and, as an extra precaution, only when the battery capacity reported through ACPI does not match what is reported through DMI (I've never encountered a machine where the first two conditions would be true but the last would not, but better safe than sorry). I've been using this patch for close to a year on several systems without any problems. References: https://bugzilla.kernel.org/show_bug.cgi?id=41062 Acked-by: Henrique de Moraes Holschuh Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

USB: mark uas driver as BROKEN

2012-12-17T18:49:04Z

commit fb37ef98015f864d22be223a0e0d93547cd1d4ef upstream. As reported https://bugzilla.kernel.org/show_bug.cgi?id=51031, the UAS driver causes problems and has been asked to be not built into any of the major distributions. To prevent users from running into problems with it, and for distros that were not notified, just mark the whole thing as broken. Acked-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman

USB: cp210x: add Virtenio Preon32 device id

2012-12-17T18:49:04Z

commit 356fe44f4b8ece867bdb9876b1854d7adbef9de2 upstream. Signed-off-by: Markus Becker Signed-off-by: Greg Kroah-Hartman

usb: ftdi_sio: fixup BeagleBone A5+ quirk

2012-12-17T18:49:04Z

commit 1a88d5eee2ef2ad1d3c4e32043e9c4c5347d4fc1 upstream. BeagleBone A5+ devices ended up getting shipped with the 'BeagleBone/XDS100V2' product string, and not XDS100 like it was agreed, so adjust the quirk to match. For details, see the thread on the beagle list: https://groups.google.com/forum/#!msg/beagleboard/zrFPew9_Wvo/ibWr1-eE8JwJ Signed-off-by: Peter Korsgaard Signed-off-by: Greg Kroah-Hartman

USB: ftdi_sio: Add support for Newport AGILIS motor drivers

2012-12-17T18:49:04Z

commit d7e14b375b40c04cd735b115713043b69a2c68ac upstream. The Newport AGILIS model AG-UC8 compact piezo motor controller (http://search.newport.com/?q=*&x2=sku&q2=AG-UC8) is yet another device using an FTDI USB-to-serial chip. It works fine with the ftdi_sio driver when adding options ftdi-sio product=0x3000 vendor=0x104d to modprobe.d. udevadm reports "Newport" as the manufacturer, and "Agilis" as the product name. Signed-off-by: Martin Teichmann Signed-off-by: Greg Kroah-Hartman

USB: option: blacklist network interface on Huawei E173

2012-12-17T18:49:03Z

commit f36446cf9bbebaa03a80d95cfeeafbaf68218249 upstream. The Huawei E173 will normally appear as 12d1:1436 in Linux. But the modem has another mode with different device ID and a slightly different set of descriptors. This is the mode used by Windows like this: 3Modem: USB\VID_12D1&PID_140C&MI_00\6&3A1D2012&0&0000 Networkcard: USB\VID_12D1&PID_140C&MI_01\6&3A1D2012&0&0001 Appli.Inter: USB\VID_12D1&PID_140C&MI_02\6&3A1D2012&0&0002 PC UI Inter: USB\VID_12D1&PID_140C&MI_03\6&3A1D2012&0&0003 All interfaces have the same ff/ff/ff class codes in this mode. Blacklisting the network interface to allow it to be picked up by the network driver. Reported-by: Thomas Schäfer Signed-off-by: Bjørn Mork Signed-off-by: Greg Kroah-Hartman