linux/drivers/usb/misc/Makefile, branch v2.6.19

USB: move trancevibrator.c to the proper usb directory

2006-10-17T21:46:32Z

It's not a input driver, so it doesn't belong in the input directory. Cc: Sam Hocevar Cc: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman

USB: ftdi-elan: client driver for ELAN Uxxx adapters

2006-09-27T18:58:59Z

This "ftdi-elan" module is one half of the "driver" for ELAN's Uxxx series adapters which are USB to PCMCIA CardBus adapters. Currently only the U132 adapter is available and it's module is called "u132-hcd". When the USB hot plug subsystem detects a Uxxx series adapter it should load this module. Upon a successful device probe() the jtag device file interface is created and the status workqueue started up. The jtag device file interface exists for the purpose of updating the firmware in the Uxxx series adapter, but as yet it had never been used. The status workqueue initializes the Uxxx and then sits there polling the Uxxx until a supported PCMCIA CardBus device is detected it will start the command and respond workqueues and then load the module that handles the device. This will initially be only the u132-hcd module. The status workqueue then just polls the Uxxx looking for card ejects. The command and respond workqueues implement a command sequencer for communicating with the firmware on the other side of the FTDI chip in the Uxxx. This "ftdi-elan" module exports some functions to interface with the sequencer. Note that this module is a USB client driver. Note that the "u132-hcd" module is a (cut-down OHCI) host controller. Thus we have a topology with the parent of a host controller being a USB client! This really stresses the USB subsystem semaphore/mutex handling in the module removal. Signed-off-by: Tony Olech Signed-off-by: Greg Kroah-Hartman

USB: Add ADU support for Ontrak ADU devices

2006-09-27T18:58:59Z

This patch adds support for Ontrak ADU USB devices. Fixed for printk issues by Randy Dunlap Signed-off-by: Steven Haigh Signed-off-by: Greg Kroah-Hartman

USB: Put phidgets driver in a sysfs class

2006-09-27T18:58:49Z

This patch creates a device class phidget and add the phidget drivers to them. Signed-off-by: Sean Young Signed-off-by: Greg Kroah-Hartman

USB: Add driver for PhidgetMotorControl

2006-09-27T18:58:49Z

This driver add support for the Phidgets Inc., MotorControl via sysfs. Also some minor fixes for the InterfaceKit. Signed-off-by: Sean Young Signed-off-by: Greg Kroah-Hartman

[PATCH] USB: rename Cypress CY7C63xxx driver to proper name and fix up some tiny things

2006-07-12T23:03:21Z

This is a new driver for the Cypress CY7C63xxx mirco controller series. It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus GmbH. It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I ported to kernel 2.6 using sysfs. I intend to support more controllers of this family (and more features) as soon as I get hold of the required IDs etc. Please see the source code's header for more information. Signed-off-by: Oliver Bock Signed-off-by: Greg Kroah-Hartman

[PATCH] USB: new driver for Cypress CY7C63xxx mirco controllers

2006-06-21T22:04:17Z

[PATCH] Driver for Apple Cinema Display

2006-06-21T22:04:14Z

This is a driver to control the brightness of an Apple Cinema Display over USB. It updates the local brightness value if the user presses a button on the display. Signed-off-by: Michael Hanselmann Cc: Oliver Neukum Cc: Paul Mackerras Cc: Benjamin Herrenschmidt Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman

[PATCH] USB: move CONFIG_USB_DEBUG checks into the Makefile

2005-11-17T19:29:55Z

This lets us remove a lot of code in the drivers that were all checking the same thing. It also found some bugs in a few of the drivers, which has been fixed up. Signed-off-by: Greg Kroah-Hartman Signed-off-by: Linus Torvalds

[PATCH] USB: add ldusb driver

2005-07-12T18:52:57Z

The following driver provides complete interrupt-in and interrupt-out reports (raw data) to a user program. Until now it uses the HIDIOCGDEVINFO ioctl call, because I don't know better :-(. Perhaps, it will be ok for you - and I will be happy, if you assign 8 minor numbers. I have tested it in several environments and it works very well for me. However, it has a problem with two or more devices at the same hub, if the two or more devices need 1 ms interrupt-in transfers. Unfortunately more than one interrupt-in transfer every ms isn't possible (ehci driver?). This is why the min_interrupt_in_interval and min_interrupt_out_interval are increased to 2 ms (see the corresponding module parameters). This way, I can use two devices simultaneously at the same hub. Signed-off-by: Michael Hund Signed-off-by: Greg Kroah-Hartman