linux/drivers/usb/core, branch v3.0.3

usb/config: use proper endian access for wMaxPacketSize

2011-08-17T17:55:51Z

commit 7de7c7d2cb49900e0b967be871bf695c7d6135c9 upstream. wMaxPacketSize is __le16 and should be accessed as such. Also fix the wBytesPerInterval assignment while here. v2: also fix the wBytesPerInterval assigment, noticed by Matt Evans This patch should be backported to the 3.0 kernel. Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Sarah Sharp Acked-by: Matt Evans Signed-off-by: Greg Kroah-Hartman

USB: additional regression fix for device removal

2011-07-07T20:29:33Z

Commit e534c5b831c8b8e9f5edee5c8a37753c808b80dc (USB: fix regression occurring during device removal) didn't go far enough. It failed to take into account that when a driver claims multiple interfaces, it may release them all at the same time. As a result, some interfaces can get released before they are unregistered, and we deadlock trying to acquire the bandwidth_mutex that we already own. This patch (asl478) handles this case by setting the "unregistering" flag on all the interfaces before removing any of them. Signed-off-by: Alan Stern Cc: stable Tested-by: Éric Piel Signed-off-by: Greg Kroah-Hartman

USB: fix regression occurring during device removal

2011-07-01T21:20:39Z

This patch (as1476) fixes a regression introduced by fccf4e86200b8f5edd9a65da26f150e32ba79808 (USB: Free bandwidth when usb_disable_device is called). usb_disconnect() grabs the bandwidth_mutex before calling usb_disable_device(), which calls down indirectly to usb_set_interface(), which tries to acquire the bandwidth_mutex. The fix causes usb_set_interface() to return early when it is called for an interface that has already been unregistered, which is what happens in usb_disable_device(). Signed-off-by: Alan Stern Tested-by: Sarah Sharp Cc: stable Signed-off-by: Greg Kroah-Hartman

Merge branch 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6

2011-06-28T18:15:17Z

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: MAINTAINERS: add myself as maintainer of USB/IP usb: r8a66597-hcd: fix cannot detect low/full speed device USB: ehci-ath79: fix a NULL pointer dereference USB: Add new FT232H chip to drivers/usb/serial/ftdi_sio.c usb/isp1760: Fix bug preventing the unlinking of control urbs USB: Fix up URB error codes to reflect implementation. xhci: Always set urb->status to zero for isoc endpoints. xhci: Add reset on resume quirk for asrock p67 host xHCI 1.0: Incompatible Device Error USB: don't let errors prevent system sleep USB: don't let the hub driver prevent system sleep USB: change maintainership of ohci-hcd and ehci-hcd xHCI 1.0: Force Stopped Event(FSE) xhci: Don't warn about zeroed bMaxBurst descriptor field. USB: Free bandwidth when usb_disable_device is called. xhci: Reject double add of active endpoints. USB: TI 3410/5052 USB Serial Driver: Fix mem leak when firmware is too big. usb: musb: gadget: clear TXPKTRDY flag when set FLUSHFIFO usb: musb: host: compare status for negative error values

Merge branch 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

2011-06-27T20:36:47Z

* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci: USB: Fix up URB error codes to reflect implementation. xhci: Always set urb->status to zero for isoc endpoints. xhci: Add reset on resume quirk for asrock p67 host xHCI 1.0: Incompatible Device Error xHCI 1.0: Force Stopped Event(FSE) xhci: Don't warn about zeroed bMaxBurst descriptor field. USB: Free bandwidth when usb_disable_device is called. xhci: Reject double add of active endpoints.

PM: Rename dev_pm_info.in_suspend to is_prepared

2011-06-21T21:19:50Z

This patch (as1473) renames the "in_suspend" field in struct dev_pm_info to "is_prepared", in preparation for an upcoming change. The new name is more descriptive of what the field really means. Signed-off-by: Alan Stern Signed-off-by: Rafael J. Wysocki Cc: stable@kernel.org

USB: don't let errors prevent system sleep

2011-06-16T00:44:56Z

This patch (as1464) implements the recommended policy that most errors during suspend or hibernation should not prevent the system from going to sleep. In particular, failure to suspend a USB driver or a USB device should not prevent the sleep from succeeding: Failure to suspend a device won't matter, because the device will automatically go into suspend mode when the USB bus stops carrying packets. (This might be less true for USB-3.0 devices, but let's not worry about them now.) Failure of a driver to suspend might lead to trouble later on when the system wakes up, but it isn't sufficient reason to prevent the system from going to sleep. Signed-off-by: Alan Stern CC: Signed-off-by: Greg Kroah-Hartman

USB: don't let the hub driver prevent system sleep

2011-06-16T00:44:56Z

This patch (as1465) continues implementation of the policy that errors during suspend or hibernation should not prevent the system from going to sleep. In this case, failure to turn on the Suspend feature for a hub port shouldn't be reported as an error. There are situations where this does actually occur (such as when the device plugged into that port was disconnected in the recent past), and it turns out to be harmless. There's no reason for it to prevent a system sleep. Also, don't allow the hub driver to fail a system suspend if the downstream ports aren't all suspended. This is also harmless (and should never happen, given the change mentioned above); printing a warning message in the kernel log is all we really need to do. Signed-off-by: Alan Stern CC: Signed-off-by: Greg Kroah-Hartman

USB: Free bandwidth when usb_disable_device is called.

2011-06-15T21:05:18Z

Tanya ran into an issue when trying to switch a UAS device from the BOT configuration to the UAS configuration via the bConfigurationValue sysfs file. Before installing the UAS configuration, set_bConfigurationValue() calls usb_disable_device(). That function is supposed to remove all host controller resources associated with that device, but it leaves some state in the xHCI host controller. Commit 0791971ba8fbc44e4f476079f856335ed45e6324 usb: allow drivers to use allocated bandwidth until unbound added a call to usb_disable_device() in usb_set_configuration(), before the xHCI bandwidth functions were invoked. That commit fixed a bug, but also introduced a bug that is triggered when a configured device is switched to a new configuration. usb_disable_device() goes through all the motions of unbinding the drivers attached to active interfaces and removing the USB core structures associated with those interfaces, but it doesn't actually remove the endpoints from the internal xHCI host controller bandwidth structures. When usb_disable_device() calls usb_disable_endpoint() with reset_hardware set to true, the entries in udev->ep_out and udev->ep_in will be set to NULL. Usually, when the USB core installs a new configuration, usb_hcd_alloc_bandwidth() will drop all non-NULL endpoints in udev->ep_out and udev->ep_in before adding any new endpoints. However, when the new UAS configuration was added, all those entries were null, so none of the old endpoints in the BOT configuration were dropped. The xHCI driver blindly added the UAS configuration endpoints, and some of the endpoint addresses overlapped with the old BOT configuration endpoints. This caused the xHCI host to reject the Configure Endpoint command. Now that the xHCI driver code is cleaned up to reject a double-add of active endpoints, we need to fix the USB core to properly drop old endpoints in usb_disable_device(). If the host controller driver needs bandwidth checking support, make usb_disable_device() call usb_disable_endpoint() with reset_hardware set to false, drop the endpoints from the xHCI host controller, and then call usb_disable_endpoint() again with reset_hardware set to true. The first call to usb_disable_endpoint() will cancel any pending URBs and wait on them to be freed in usb_hcd_disable_endpoint(), but will keep the pointers in udev->ep_out and udev->ep in intact. Then usb_hcd_alloc_bandwidth() will use those pointers to know which endpoints to drop. The final call to usb_disable_endpoint() will do two things: 1. It will call usb_hcd_disable_endpoint() again, which should be harmless since the ep->urb_list should be empty after the first call to usb_disable_endpoint() returns. 2. It will set the entries in udev->ep_out and udev->ep in to NULL, and call usb_hcd_disable_endpoint(). That call will have no effect, since the xHCI driver doesn't set the endpoint_disable function pointer. Note that usb_disable_device() will now need to be called with hcd->bandwidth_mutex held. This should be backported to kernels as old as 2.6.32. Signed-off-by: Sarah Sharp Reported-by: Tanya Brokhman Cc: ablay@codeaurora.org Cc: Alan Stern Cc: stable@kernel.org

usb: remove bad dput after dentry_unhash

2011-06-06T23:26:59Z

Commit 64252c75a (vfs: remove dget() from dentry_unhash()) removed the useless dget from dentry_unhash but didn't fix up this caller in the usb code. There used to be exactly one dput per dentry_unhash call; now there are none. Tested-by: Sebastian Andrzej Siewior Signed-off-by: Sage Weil Signed-off-by: Greg Kroah-Hartman