linux/drivers/net/phy/phy.c, branch v3.10.2

net: phy: fix a bug when verify the EEE support

2013-05-28T06:30:09Z

The phy_init_eee has to exit with an error when the local device and its link partner both do not support EEE. So this patch fixes a problem when verify this. Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller

phy: Elimination the forced speed reduction algorithm.

2013-03-27T17:10:43Z

In case of fixed speed set up for a NIC (e.g. ethtool -s eth0 autoneg off speed 100 duplex full) with an ethernet cable plugged off, the mentioned algorithm slows down a NIC speed, so further cable hook-up leads to nonoperable link state. Signed-off-by: Kirill Kapranov Signed-off-by: David S. Miller

phy: add set_wol/get_wol functions

2013-03-12T15:40:53Z

This allows ethernet drivers (such as the mv643xx_eth) to support Wake on LAN on platforms where PHY registers have to be configured for Wake on LAN (e.g. the Marvell Kirkwood based qnap TS-119P II). Signed-off-by: Michael Stapelberg Signed-off-by: David S. Miller

mdio: translation of MMD EEE registers to/from ethtool settings

2012-08-23T05:58:27Z

The helper functions which translate IEEE MDIO Manageable Device (MMD) Energy-Efficient Ethernet (EEE) registers 3.20, 7.60 and 7.61 to and from the comparable ethtool supported/advertised settings will be needed by drivers other than those in PHYLIB (e.g. e1000e in a follow-on patch). In the same fashion as similar translation functions in linux/mii.h, move these functions from the PHYLIB core to the linux/mdio.h header file so the code will not have to be duplicated in each driver needing MMD-to-ethtool (and vice-versa) translations. The function and some variable names have been renamed to be more descriptive. Not tested on the only hardware that currently calls the related functions, stmmac, because I don't have access to any. Has been compile tested and the translations have been tested on a locally modified version of e1000e. Signed-off-by: Bruce Allan Cc: Giuseppe Cavallaro Signed-off-by: David S. Miller

phy: add the EEE support and the way to access to the MMD registers.

2012-07-01T10:34:50Z

This patch adds the support for the Energy-Efficient Ethernet (EEE) to the Physical Abstraction Layer. To support the EEE we have to access to the MMD registers 3.20 and 7.60/61. So two new functions have been added to read/write the MMD registers (clause 45). An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly check if the EEE is supported by the PHYs and it can also set the clock stop enable bit in the 3.0 register. The phy_get_eee_err can be used for reporting the number of time where the PHY failed to complete its normal wake sequence. In the end, this patch also adds the EEE ethtool support implementing: o phy_ethtool_set_eee o phy_ethtool_get_eee v1: initial patch v2: fixed some errors especially on naming convention v3: renamed again the mmd read/write functions thank to Ben's feedback v4: moved file to phy.c and added the ethtool support. v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return values according to ethtool API (thanks to Ben's feedback). Renamed some macros to avoid too long names. v6: fixed kernel-doc comments to be properly parsed. Fixed the phy_init_eee function: we need to check which link mode was autonegotiated and then the corresponding bits in 7.60 and 7.61 registers. v7: reviewed the way to get the negotiated settings. v8: fixed a problem in the phy_init_eee return value erroneously added when included the phy_read_status call. v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16. Signed-off-by: Giuseppe Cavallaro Reviewed-by: Ben Hutchings Signed-off-by: David S. Miller

phy: Use pr_

2012-06-11T23:58:24Z

Use a more current logging style. Add pr_fmt and missing newlines. Remove embedded prefixes. Neaten phy_print_status to avoid using KERN_CONT. Signed-off-by: Joe Perches Signed-off-by: David S. Miller

atomic: use

2011-07-26T23:49:47Z

This allows us to move duplicated code in (atomic_inc_not_zero() for now) to Signed-off-by: Arun Sharma Reviewed-by: Eric Dumazet Cc: Ingo Molnar Cc: David Miller Cc: Eric Dumazet Acked-by: Mike Frysinger Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

ethtool: cosmetic: Use ethtool ethtool_cmd_speed API

2011-04-29T21:03:01Z

This updates the network drivers so that they don't access the ethtool_cmd::speed field directly, but use ethtool_cmd_speed() instead. For most of the drivers, these changes are purely cosmetic and don't fix any problem, such as for those 1GbE/10GbE drivers that indirectly call their own ethtool get_settings()/mii_ethtool_gset(). The changes are meant to enforce code consistency and provide robustness with future larger throughputs, at the expense of a few CPU cycles for each ethtool operation. All drivers compiled with make allyesconfig ion x86_64 have been updated. Tested: make allyesconfig on x86_64 + e1000e/bnx2x work Signed-off-by: David Decotigny Signed-off-by: David S. Miller

ethtool: Use full 32 bit speed range in ethtool's set_settings

2011-04-29T21:03:00Z

This makes sure the ethtool's set_settings() callback of network drivers don't ignore the 16 most significant bits when ethtool calls their set_settings(). All drivers compiled with make allyesconfig on x86_64 have been updated. Signed-off-by: David Decotigny Signed-off-by: David S. Miller

phylib: SIOCGMIIREG/SIOCSMIIREG: allow access to all mdio addresses

2011-03-14T22:02:14Z

phylib would silently ignore the phy_id argument to these ioctls and perform the read/write with the active phydev address, whereas most non-phylib drivers seem to allow access to all mdio addresses (E.G. pcnet_cs). Signed-off-by: Peter Korsgaard Signed-off-by: David S. Miller