linux/drivers/net/phy/phy.c, branch v3.0.31

ethtool: cosmetic: Use ethtool ethtool_cmd_speed API

2011-04-29T21:03:01Z

This updates the network drivers so that they don't access the ethtool_cmd::speed field directly, but use ethtool_cmd_speed() instead. For most of the drivers, these changes are purely cosmetic and don't fix any problem, such as for those 1GbE/10GbE drivers that indirectly call their own ethtool get_settings()/mii_ethtool_gset(). The changes are meant to enforce code consistency and provide robustness with future larger throughputs, at the expense of a few CPU cycles for each ethtool operation. All drivers compiled with make allyesconfig ion x86_64 have been updated. Tested: make allyesconfig on x86_64 + e1000e/bnx2x work Signed-off-by: David Decotigny Signed-off-by: David S. Miller

ethtool: Use full 32 bit speed range in ethtool's set_settings

2011-04-29T21:03:00Z

This makes sure the ethtool's set_settings() callback of network drivers don't ignore the 16 most significant bits when ethtool calls their set_settings(). All drivers compiled with make allyesconfig on x86_64 have been updated. Signed-off-by: David Decotigny Signed-off-by: David S. Miller

phylib: SIOCGMIIREG/SIOCSMIIREG: allow access to all mdio addresses

2011-03-14T22:02:14Z

phylib would silently ignore the phy_id argument to these ioctls and perform the read/write with the active phydev address, whereas most non-phylib drivers seem to allow access to all mdio addresses (E.G. pcnet_cs). Signed-off-by: Peter Korsgaard Signed-off-by: David S. Miller

net: add some KERN_CONT markers to continuation lines

2010-11-28T18:47:17Z

Cc: netdev@vger.kernel.org Signed-off-by: Uwe Kleine-König Signed-off-by: David S. Miller

phylib: make local function static

2010-10-24T22:07:11Z

The following functions are not used directly by any drivers: phy_attach_direct phy_device_create phy_prepare_link genphy_config_advert genphy_setup_forced phy_config_interrupt phy_clear_interrypt phy_sanitize_settings phy_enable_interrupts phy_disable_interrupts Signed-off-by: Stephen Hemminger Signed-off-by: David S. Miller

phy.c: fix kernel-doc warnings

2010-08-10T07:09:21Z

Fix phy.c kernel-doc notation: Warning(drivers/net/phy/phy.c:313): No description found for parameter 'ifr' Warning(drivers/net/phy/phy.c:313): Excess function parameter 'mii_data' description in 'phy_mii_ioctl' Signed-off-by: Randy Dunlap Signed-off-by: David S. Miller

net: support time stamping in phy devices.

2010-07-19T02:15:26Z

This patch adds a new networking option to allow hardware time stamps from PHY devices. When enabled, likely candidates among incoming and outgoing network packets are offered to the PHY driver for possible time stamping. When accepted by the PHY driver, incoming packets are deferred for later delivery by the driver. The patch also adds phylib driver methods for the SIOCSHWTSTAMP ioctl and callbacks for transmit and receive time stamping. Drivers may optionally implement these functions. Signed-off-by: Richard Cochran Signed-off-by: David S. Miller

net: preserve ifreq parameter when calling generic phy_mii_ioctl().

2010-07-19T02:15:25Z

The phy_mii_ioctl() function unnecessarily throws away the original ifreq. We need access to the ifreq in order to support PHYs that can perform hardware time stamping. Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl(). This is unnecessary since phylib will check the command in any case. Signed-off-by: Richard Cochran Signed-off-by: David S. Miller

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

2010-03-30T13:02:32Z

percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo Guess-its-ok-by: Christoph Lameter Cc: Ingo Molnar Cc: Lee Schermerhorn

phylib: Move workqueue initialization to a proper place

2010-01-19T09:59:02Z

commit 541cd3ee00a4fe975b22fac6a3bc846bacef37f7 ("phylib: Fix deadlock on resume") caused TI DaVinci EMAC ethernet driver to oops upon resume: PM: resume of devices complete after 237.098 msecs Restarting tasks ... done. kernel BUG at kernel/workqueue.c:354! Unable to handle kernel NULL pointer dereference at virtual address 00000000 [...] Backtrace: [] (__bug+0x0/0x2c) from [] (queue_delayed_work_on+0x74/0xf8) [] (queue_delayed_work_on+0x0/0xf8) from [] (queue_delayed_work+0x2c/0x30) The oops pops up because TI DaVinci EMAC driver detaches PHY on suspend and attaches it back on resume. Attaching makes phylib call phy_start_machine() that initializes a workqueue. On the other hand, PHY's resume routine will call phy_start_machine() again, and that will cause the oops since we just destroyed the already scheduled workqueue. This patch fixes the issue by moving workqueue initialization to phy_device_create(). p.s. We don't see this oops with ucc_geth and gianfar drivers because they perform a fine-grained suspend, i.e. they just stop the PHYs without detaching. Reported-by: Sekhar Nori Signed-off-by: Anton Vorontsov Tested-by: Sekhar Nori Signed-off-by: David S. Miller