linux/drivers/md, branch v3.4.80

dm space map common: make sure new space is used during extend

2014-02-13T19:51:14Z

commit 12c91a5c2d2a8e8cc40a9552313e1e7b0a2d9ee3 upstream. When extending a low level space map we should update nr_blocks at the start so the new space is used for the index entries. Otherwise extend can fail, e.g.: sm_metadata_extend call sequence that fails: -> sm_ll_extend -> dm_tm_new_block -> dm_sm_new_block -> sm_bootstrap_new_block => returns -ENOSPC because smm->begin == smm->ll.nr_blocks Signed-off-by: Joe Thornber Signed-off-by: Mike Snitzer Signed-off-by: Greg Kroah-Hartman

dm: wait until embedded kobject is released before destroying a device

2014-02-13T19:51:14Z

commit be35f486108227e10fe5d96fd42fb2b344c59983 upstream. There may be other parts of the kernel holding a reference on the dm kobject. We must wait until all references are dropped before deallocating the mapped_device structure. The dm_kobject_release method signals that all references are dropped via completion. But dm_kobject_release doesn't free the kobject (which is embedded in the mapped_device structure). This is the sequence of operations: * when destroying a DM device, call kobject_put from dm_sysfs_exit * wait until all users stop using the kobject, when it happens the release method is called * the release method signals the completion and should return without delay * the dm device removal code that waits on the completion continues * the dm device removal code drops the dm_mod reference the device had * the dm device removal code frees the mapped_device structure that contains the kobject Using kobject this way should avoid the module unload race that was mentioned at the beginning of this thread: https://lkml.org/lkml/2014/1/4/83 Signed-off-by: Mikulas Patocka Signed-off-by: Mike Snitzer Signed-off-by: Greg Kroah-Hartman

md/raid5: fix long-standing problem with bitmap handling on write failure.

2014-02-06T19:05:46Z

commit 9f97e4b128d2ea90a5f5063ea0ee3b0911f4c669 upstream. Before a write starts we set a bit in the write-intent bitmap. When the write completes we clear that bit if the write was successful to all devices. However if the write wasn't fully successful we should not clear the bit. If the faulty drive is subsequently re-added, the fact that the bit is still set ensure that we will re-write the data that is missing. This logic is mediated by the STRIPE_DEGRADED flag - we only clear the bitmap bit when this flag is not set. Currently we correctly set the flag if a write starts when some devices are failed or missing. But we do *not* set the flag if some device failed during the write attempt. This is wrong and can result in clearing the bit inappropriately. So: set the flag when a write fails. This bug has been present since bitmaps were introduces, so the fix is suitable for any -stable kernel. Reported-by: Ethan Wilson Signed-off-by: NeilBrown Signed-off-by: Greg Kroah-Hartman

md/raid10: fix two bugs in handling of known-bad-blocks.

2014-01-29T13:10:42Z

commit b50c259e25d9260b9108dc0c2964c26e5ecbe1c1 upstream. If we discover a bad block when reading we split the request and potentially read some of it from a different device. The code path of this has two bugs in RAID10. 1/ we get a spin_lock with _irq, but unlock without _irq!! 2/ The calculation of 'sectors_handled' is wrong, as can be clearly seen by comparison with raid1.c This leads to at least 2 warnings and a probable crash is a RAID10 ever had known bad blocks. Fixes: 856e08e23762dfb92ffc68fd0a8d228f9e152160 Reported-by: Damian Nowak URL: https://bugzilla.kernel.org/show_bug.cgi?id=68181 Signed-off-by: NeilBrown Signed-off-by: Greg Kroah-Hartman

md/raid10: fix bug when raid10 recovery fails to recover a block.

2014-01-29T13:10:42Z

commit e8b849158508565e0cd6bc80061124afc5879160 upstream. commit e875ecea266a543e643b19e44cf472f1412708f9 md/raid10 record bad blocks as needed during recovery. added code to the "cannot recover this block" path to record a bad block rather than fail the whole recovery. Unfortunately this new case was placed *after* r10bio was freed rather than *before*, yet it still uses r10bio. This is will crash with a null dereference. So move the freeing of r10bio down where it is safe. Fixes: e875ecea266a543e643b19e44cf472f1412708f9 Reported-by: Damian Nowak URL: https://bugzilla.kernel.org/show_bug.cgi?id=68181 Signed-off-by: NeilBrown Signed-off-by: Greg Kroah-Hartman

dm table: fail dm_table_create on dm_round_up overflow

2013-12-20T15:34:20Z

commit 5b2d06576c5410c10d95adfd5c4d8b24de861d87 upstream. The dm_round_up function may overflow to zero. In this case, dm_table_create() must fail rather than go on to allocate an empty array with alloc_targets(). This fixes a possible memory corruption that could be caused by passing too large a number in "param->target_count". Signed-off-by: Mikulas Patocka Signed-off-by: Mike Snitzer Signed-off-by: Greg Kroah-Hartman

dm delay: fix a possible deadlock due to shared workqueue

2013-12-20T15:34:20Z

commit 718822c1c112dc99e0c72c8968ee1db9d9d910f0 upstream. The dm-delay target uses a shared workqueue for multiple instances. This can cause deadlock if two or more dm-delay targets are stacked on the top of each other. This patch changes dm-delay to use a per-instance workqueue. Signed-off-by: Mikulas Patocka Signed-off-by: Mike Snitzer Signed-off-by: Greg Kroah-Hartman

dm bufio: initialize read-only module parameters

2013-12-20T15:34:20Z

commit 4cb57ab4a2e61978f3a9b7d4f53988f30d61c27f upstream. Some module parameters in dm-bufio are read-only. These parameters inform the user about memory consumption. They are not supposed to be changed by the user. However, despite being read-only, these parameters can be set on modprobe or insmod command line, for example: modprobe dm-bufio current_allocated_bytes=12345 The kernel doesn't expect that these variables can be non-zero at module initialization and if the user sets them, it results in BUG. This patch initializes the variables in the module init routine, so that user-supplied values are ignored. Signed-off-by: Mikulas Patocka Signed-off-by: Mike Snitzer Signed-off-by: Greg Kroah-Hartman

dm: fix truncated status strings

2013-12-08T15:29:43Z

commit fd7c092e711ebab55b2688d3859d95dfd0301f73 upstream. Avoid returning a truncated table or status string instead of setting the DM_BUFFER_FULL_FLAG when the last target of a table fills the buffer. When processing a table or status request, the function retrieve_status calls ti->type->status. If ti->type->status returns non-zero, retrieve_status assumes that the buffer overflowed and sets DM_BUFFER_FULL_FLAG. However, targets don't return non-zero values from their status method on overflow. Most targets returns always zero. If a buffer overflow happens in a target that is not the last in the table, it gets noticed during the next iteration of the loop in retrieve_status; but if a buffer overflow happens in the last target, it goes unnoticed and erroneously truncated data is returned. In the current code, the targets behave in the following way: * dm-crypt returns -ENOMEM if there is not enough space to store the key, but it returns 0 on all other overflows. * dm-thin returns errors from the status method if a disk error happened. This is incorrect because retrieve_status doesn't check the error code, it assumes that all non-zero values mean buffer overflow. * all the other targets always return 0. This patch changes the ti->type->status function to return void (because most targets don't use the return code). Overflow is detected in retrieve_status: if the status method fills up the remaining space completely, it is assumed that buffer overflow happened. Signed-off-by: Mikulas Patocka Signed-off-by: Alasdair G Kergon Signed-off-by: Greg Kroah-Hartman

md: fix calculation of stacking limits on level change.

2013-12-04T18:50:33Z

commit 02e5f5c0a0f726e66e3d8506ea1691e344277969 upstream. The various ->run routines of md personalities assume that the 'queue' has been initialised by the blk_set_stacking_limits() call in md_alloc(). However when the level is changed (by level_store()) the ->run routine for the new level is called for an array which has already had the stacking limits modified. This can result in incorrect final settings. So call blk_set_stacking_limits() before ->run in level_store(). A specific consequence of this bug is that it causes discard_granularity to be set incorrectly when reshaping a RAID4 to a RAID0. This is suitable for any -stable kernel since 3.3 in which blk_set_stacking_limits() was introduced. Reported-and-tested-by: "Baldysiak, Pawel" Signed-off-by: NeilBrown Signed-off-by: Greg Kroah-Hartman