linux/drivers/input/tablet, branch v3.5-rc3

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2012-05-24T17:34:29Z

Pull input layer updates from Dmitry Torokhov: - a bunch of new drivers (DA9052/53 touchscreenn controller, Synaptics Navpoint, LM8333 keypads, Wacom I2C touhscreen); - updates to existing touchpad drivers (ALPS, Sntelic); - Wacom driver now supports Intuos5; - device-tree bindings in numerous drivers; - other cleanups and fixes. Fix annoying conflict in drivers/input/tablet/wacom_wac.c that I think implies that the input layer device naming is broken, but let's see. I brough it up with Dmitry. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits) Input: matrix-keymap - fix building keymaps Input: spear-keyboard - document DT bindings Input: spear-keyboard - add device tree bindings Input: matrix-keymap - wire up device tree support Input: matrix-keymap - uninline and prepare for device tree support Input: adp5588 - add support for gpio names Input: omap-keypad - dynamically handle register offsets Input: synaptics - fix compile warning MAINTAINERS: adjust input-related patterns Input: ALPS - switch to using input_mt_report_finger_count Input: ALPS - add semi-MT support for v4 protocol Input: Add Synaptics NavPoint (PXA27x SSP/SPI) driver Input: atmel_mxt_ts - dump each message on just 1 line Input: atmel_mxt_ts - do not read extra (checksum) byte Input: atmel_mxt_ts - verify object size in mxt_write_object Input: atmel_mxt_ts - only allow root to update firmware Input: atmel_mxt_ts - use CONFIG_PM_SLEEP Input: sentelic - report device's production serial number Input: tl6040-vibra - Device Tree support Input: evdev - properly handle read/write with count 0 ...

USB: input: wacom_sys.c: fix up dev_* messages

2012-05-04T22:33:13Z

Previously I had made the struct device point to the input device, but after talking with Dmitry, he said that the USB device would make more sense for this driver to point to. So converted it to use that instead. CC: Dmitry Torokhov CC: Ping Cheng CC: Chris Bagwell CC: Eduard Hasenleithner Signed-off-by: Greg Kroah-Hartman

USB: input: kbtab.c: fix up dev_* messages

2012-05-04T22:33:11Z

USB: input: gtco.c: fix up dev_* messages

2012-05-04T22:33:09Z

USB: input: aiptek.c: fix up dev_* messages

2012-05-04T22:33:06Z

Previously I had made the struct device point to the input device, but after talking with Dmitry, he said that the USB device would make more sense for this driver to point to. So converted it to use that instead. CC: Dmitry Torokhov CC: Jesper Juhl CC: JJ Ding CC: Edwin van Vliet Signed-off-by: Greg Kroah-Hartman

USB: input: acecad.c: fix up dev_* messages

2012-05-04T22:33:04Z

Input: wacom - use dev_xxx() instead of naked printk()s and dbg()s

2012-05-02T07:20:51Z

Reviewed-by: Chris Bagwell Signed-off-by: Dmitry Torokhov

Input: wacom - return proper error if usb_get_extra_descriptor() fails

2012-05-02T07:20:30Z

Instead of returning 1 (which is not even negative) let's capture and return error codde returned by usb_get_extra_descriptor(). Reviewed-by: Chris Bagwell Signed-off-by: Dmitry Torokhov

Input: wacom - fix sparse warning

2012-05-02T07:19:52Z

This fixes the following warning from sparse warning: Using plain integer as NULL pointer Reviewed-by: Chris Bagwell Signed-off-by: Dmitry Torokhov

USB: kbtab.c: remove dbg() usage

2012-05-02T04:33:20Z

dbg() was a very old USB-specific macro that should no longer be used. This patch removes it from being used in the driver and uses dev_dbg() instead. CC: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman