linux/drivers/input/tablet, branch v3.4.9

Input: wacom - Bamboo One 1024 pressure fix

2012-08-15T15:10:34Z

commit 6dc463511d4a690f01a9248df3b384db717e0b1c upstream. Bamboo One's with ID of 0x6a and 0x6b were added with correct indication of 1024 pressure levels but the Graphire packet routine was only looking at 9 bits. Increased to 10 bits. This bug caused these devices to roll over to zero pressure at half way mark. The other devices using this routine only support 256 or 512 range and look to fix unused bits at zero. Signed-off-by: Chris Bagwell Reported-by: Tushant Mirchandani Reviewed-by: Ping Cheng Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman

Input: wacom - check for allocation failure in probe()

2012-03-30T05:42:19Z

We accidentally removed the check for NULL in 3aac0ef10b "Input: wacom - isolate input registration". Signed-off-by: Dan Carpenter Reviewed-by: Chris Bagwell Signed-off-by: Dmitry Torokhov

Merge branch 'next' into for-linus

2012-03-27T07:27:10Z

Conflicts: drivers/input/tablet/wacom_sys.c

Input: wacom - wireless battery status

2012-03-26T06:33:17Z

Signed-off-by: Chris Bagwell Tested-by: Jason Gerecke Acked-by: Ping Cheng Signed-off-by: Dmitry Torokhov

Input: wacom - create inputs when wireless connect

2012-03-26T06:32:59Z

When a tablet connect or disconnect is detected, schedule work queue to register or unregister related input devices. When a wireless tablet connects, it reports same USB PID used if tablet is connected with USB cable. Use this to update features values, set input capabilities, and then register device. From there, the Pen and Touch interfaces will reuse the existing tablet's IRQ routines. Its possible that 1 receiver is shared with 2 tablets with different PID (small and medium Bamboo for example) so the input is unregister at disconnect to better support this case. Signed-off-by: Chris Bagwell Tested-by: Jason Gerecke Acked-by: Ping Cheng Signed-off-by: Dmitry Torokhov

Input: wacom - wireless monitor framework

2012-03-26T06:31:32Z

The 3rd gen Bamboo Pen & Touch and Intuos5 tablets support an optional wireless module. When its receiver is plugged into USB, it presents 3 interfaces: 0) Monitor 1) Pen and 2) Touch. The exact capabilities of the Pen and Touch interfaces can not be determined until a tablet connection is established and reported over the Monitor interface. This patch detects this wireless receiver and enables interrupt packets to be processed for the Monitor interface. Processing the data in packets will be left to another patch. Since it doesn't make sense to create an input device for the Monitor interface, it is not created. Creation of Pen and Touch input device is also delayed until monitor packets can be processed. Signed-off-by: Chris Bagwell Tested-by: Jason Gerecke Acked-by: Ping Cheng Signed-off-by: Dmitry Torokhov

Input: wacom - isolate input registration

2012-03-26T06:31:27Z

Although this better co-locates input registration logic, the main goal is to make it easier to optionally create input devices or delay creation to later time periods. Signed-off-by: Chris Bagwell Tested-by: Jason Gerecke Acked-by: Ping Cheng Signed-off-by: Dmitry Torokhov

Merge branch 'next' into for-linus

2012-03-20T00:02:01Z

Input: wacom - fix physical size calculation for 3rd-gen Bamboo

2012-03-13T05:19:14Z

This calculation determines the physical dimensions of the tablet, used later on in calculate_touch_res to obtain the touch sensor resolution. Instead of dividing the logical size by the resolution, the current code performs a multiplication. This doesn't pose a problem for the 3rd-gen Bamboo since the resolution and scale factor happen to be identical, but will produce an incorrect result for other cases. Signed-off-by: Jason Gerecke Reviewed-by: Chris Bagwell Signed-off-by: Dmitry Torokhov

Merge commit 'v3.3-rc6' into next

2012-03-09T18:55:17Z