linux/drivers/bluetooth, branch v3.14

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

2014-01-08T18:44:29Z

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless

2014-01-06T19:08:41Z

Bluetooth: Deal with USB devices that are faking CSR vendor

2014-01-04T18:11:07Z

There exists a set of Bluetooth USB devices that show up on the USB bus as 0a12:0001 and identify themselves as devices from CSR. However they are not. When sending Read Local Version command they now have a split personality and say they are from Broadcom. < HCI Command: Read Local Version Information (0x04|0x0001) plen 0 > HCI Event: Command Complete (0x0e) plen 12 Read Local Version Information (0x04|0x0001) ncmd 1 status 0x00 HCI Version: 2.0 (0x3) HCI Revision: 0x3000 LMP Version: 2.0 (0x3) LMP Subversion: 0x420b Manufacturer: Broadcom Corporation (15) The assumption is that they are neither CSR nor Broadcom based devices and that they are designed and manufactured by someone else. For the most parts they follow the Bluetooth HCI specification and can be used as standard Bluetooth devices. However they have the minor problem that the Delete Stored Link Key command is not working as it should. During the Bluetooth controller setup, this command is needed if stored link keys are supported. For these devices it has to be assumed that this is broken and so just set a quirk to clearly indicate the behavior. After that the setup can just proceed. Now the trick part is to detect these faulty devices since we do not want to punish all CSR and all Broadcom devices. The original devices do actually work according to the specification. What is known so far is that these broken devices set the USB bcdDevice revision information to 1.0 or less. T: Bus=02 Lev=01 Prnt=01 Port=08 Cnt=03 Dev#= 9 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a12 ProdID=0001 Rev= 1.00 S: Manufacturer=Bluetooth v2.0 S: Product=Bluetooth V2.0 Dongle T: Bus=05 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a12 ProdID=0001 Rev= 0.07 In case of CSR devices, the bcdDevice revision contains the firmware build ID and that is normally a higher value. If the bcdDevice revision is 1.0 or less, then an extra setup stage is checking if Read Local Version returns CSR manufacturer information. If not then it will be assumed that this is a broken device and the Delete Stored Link Key command will be marked as broken. Signed-off-by: Marcel Holtmann Signed-off-by: Johan Hedberg

Bluetooth: Use MD SET register for changing SDIO Type-B to Type-A

2013-12-29T19:31:07Z

The register for setting the SDIO card mode of a Type-B Bluetooth card is called MD SET. The MD STAT register is used for reading the current mode back. Signed-off-by: Marcel Holtmann Signed-off-by: Johan Hedberg

Bluetooth: Add support for vectored writes to virtual HCI driver

2013-12-29T19:25:52Z

The Bluetooth virtual HCI driver is using a misc character device to allow emulation of HCI devices from userspace. This change enables the support for vectored writes. Previously this was failing with EINVAL since no complete H:4 packet was written. Signed-off-by: Marcel Holtmann Signed-off-by: Johan Hedberg

Bluetooth: Set HCI_QUIRK_RESET_ON_CLOSE for Socket SDIO cards

2013-12-23T16:49:35Z

The Socket Bluetooth SDIO cards are branded versions of Toshiba SD-BT2 and they do not support sending HCI_Reset as first command. To make this card work the HCI_QUIRK_RESET_ON_CLOSE quirk needs to be set before registering the controller. Signed-off-by: Marcel Holtmann Signed-off-by: Johan Hedberg

Bluetooth: Add support for Toshiba Bluetooth device [0930:0220]

2013-12-04T13:11:49Z

This patch adds support for new Toshiba Bluetooth device. T: Bus=05 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=0220 Rev=00.02 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: Marco Piazza Signed-off-by: Gustavo Padovan

Bluetooth: Enable autosuspend for Intel Bluetooth device

2013-12-04T13:09:05Z

This patch enables autosuspend for Intel Bluetooth device. After btusb is loaded for Intel Bluetooth device, the power/control attribute contains "on" value by default which disables the autosuspend. Based on the USB PM document(Documentation/usb/power-management.txt), kernel disabled the autosuspend for all devices other than hub by default. "The USB specification states that all USB devices must support power management. Nevertheless, the sad fact is that many devices do not support it very well. You can suspend them all right, but when you try to resume them they disconnect themselves from the USB bus or they stop working entirely. This seems to be especially prevalent among printers and scanners, but plenty of other types of device have the same deficiency. For this reason, by default the kernel disables autosuspend (the power/control attribute is initialized to "on") for all devices other than hubs. Hubs, at least, appear to be reasonably well-behaved in this regard." This document also described how the driver can enables the autosuspend by using an USB api. "Drivers can enable autosuspend for their devices by calling usb_enable_autosuspend(struct usb_device *udev); in their probe() routine, if they know that the device is capable of suspending and resuming correctly. This is exactly equivalent to writing "auto" to the device's power/control attribute." For Intel Bluetooth device, the autosuspend needs to be enabled so the device can transit to LPM(Low Power Mode) and ULPM(Ultra LPM) states after receiving suspend message from the host. Signed-off-by: Tedd Ho-Jeong An Signed-off-by: Marcel Holtmann

Bluetooth: Add support for Intel Bluetooth device [8087:0a2a]

2013-12-04T13:09:04Z

This patch adds support for new Intel Bluetooth device. T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0a2a Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Tedd Ho-Jeong An Signed-off-by: Marcel Holtmann

Bluetooth: ath3k: Add support for a new AR3012 device

2013-12-04T13:09:04Z

T: Bus=02 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 9 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e05f Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Reported-by: Joshua Richenhagen Signed-off-by: Sujith Manoharan Signed-off-by: Johan Hedberg