linux/drivers/ata, branch v3.4.26

libata: fix Null pointer dereference on disk error

2013-01-17T16:50:44Z

commit 26cd4d65deba587f3cf2329b6869ce02bcbe68ec upstream. Following oops were observed when disk error happened: [ 4272.896937] sd 0:0:0:0: [sda] Unhandled error code [ 4272.896939] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 4272.896942] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 00 5a de a7 00 00 08 00 [ 4272.896951] end_request: I/O error, dev sda, sector 5955239 [ 4291.574947] BUG: unable to handle kernel NULL pointer dereference at (null) [ 4291.658305] IP: [] ahci_activity_show+0x1/0x40 [ 4291.730090] PGD 76dbbc067 PUD 6c4fba067 PMD 0 [ 4291.783408] Oops: 0000 [#1] SMP [ 4291.822100] last sysfs file: /sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/sw_activity [ 4291.934235] CPU 9 [ 4291.958301] Pid: 27942, comm: hwinfo ...... ata_scsi_find_dev could return NULL, so ata_scsi_activity_{show,store} should check if atadev is NULL. Signed-off-by: Xiaotian Feng Cc: James Bottomley Signed-off-by: Jeff Garzik Signed-off-by: Greg Kroah-Hartman

libata: set dma_mode to 0xff in reset

2013-01-17T16:50:44Z

commit 5416912af75de9cba5d1c75b99a7888b0bbbd2fb upstream. ata_device->dma_mode's initial value is zero, which is not a valid dma mode, but ata_dma_enabled will return true for this value. This patch sets dma_mode to 0xff in reset function, so that ata_dma_enabled will not return true for this case, or it will cause problem for pata_acpi. The corrsponding bugzilla page is at: https://bugzilla.kernel.org/show_bug.cgi?id=49151 Reported-by: Phillip Wood Signed-off-by: Aaron Lu Tested-by: Szymon Janc Tested-by: Dutra Julio Acked-by: Alan Cox Signed-off-by: Jeff Garzik Signed-off-by: Greg Kroah-Hartman

sata_promise: fix hardreset lockdep error

2013-01-17T16:50:44Z

commit 3100d49d3cd236443faae9d81137c81b22d36003 upstream. sata_promise's pdc_hard_reset_port() needs to serialize because it flips a port-specific bit in controller register that's shared by all ports. The code takes the ata host lock for this, but that's broken because an interrupt may arrive on our irq during the hard reset sequence, and that too will take the ata host lock. With lockdep enabled a big nasty warning is seen. Fixed by adding private state to the ata host structure, containing a second lock used only for serializing the hard reset sequences. This eliminated the lockdep warnings both on my test rig and on the original reporter's machine. Signed-off-by: Mikael Pettersson Tested-by: Adko Branil Signed-off-by: Jeff Garzik Signed-off-by: Greg Kroah-Hartman

sata_svw: check DMA start bit before reset

2012-12-03T19:47:11Z

commit b03e66a6be91f8389fcd902ab6c1563db1c9c06b upstream. If kdump is triggered with pending IO, controller may not respond causing kdump to fail. http://marc.info/?l=linux-ide&m=133032255424658&w=2 During error recovery ata_do_dev_read_id never completes due hang in mmio_insw. ata_do_dev_read_id ata_sff_data_xfer ioread16_rep mmio_insw if DMA start bit is cleared before reset, PIO command is successful and kdump succeeds. Signed-off-by: David Milburn Signed-off-by: Jeff Garzik Cc: CAI Qian Signed-off-by: Greg Kroah-Hartman

libata: Prevent interface errors with Seagate FreeAgent GoFlex

2012-10-02T17:30:35Z

commit c531077f40abc9f2129c4c83a30b3f8d6ce1c0e7 upstream. When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure, interface errors are always seen until 1.5Gbps is negotiated [1]. This occurs using any disk in the enclosure, and when the disk is connected directly with a generic passive eSATAp cable, we see stable 3Gbps operation as expected. Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset and renegotiation incurs. Signed-off-by: Daniel J Blueman Signed-off-by: Jeff Garzik Signed-off-by: Greg Kroah-Hartman

ahci: Add alternate identifier for the 88SE9172

2012-10-02T17:29:55Z

commit 17c60c6b763cb5b83b0185e7d38d01d18e55a05a upstream. This can also appear as 0x9192. Reported in bugzilla and confirmed with the board documentation for these boards. Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42970 Signed-off-by: Alan Cox Signed-off-by: Jeff Garzik Signed-off-by: Greg Kroah-Hartman

ata_piix: defer disks to the Hyper-V drivers by default

2012-06-17T18:21:29Z

commit cd006086fa5d91414d8ff9ff2b78fbb593878e3c upstream. When we are hosted on a Microsoft Hyper-V hypervisor the guest disks are exposed both via the Hyper-V paravirtualised drivers and via an emulated SATA disk drive. In this case we want to use the paravirtualised drivers if we can as they are much more efficient. Note that the Hyper-V paravirtualised drivers only expose the virtual hard disk devices, the CDROM/DVD devices must still be enumerated. Mark the host controller ATA_HOST_IGNORE_ATA to prevent enumeration of disk devices. BugLink: http://bugs.launchpad.net/bugs/929545 BugLink: http://bugs.launchpad.net/bugs/942316 Signed-off-by: Andy Whitcroft Signed-off-by: Jeff Garzik Cc: Victor Miasnikov Signed-off-by: Greg Kroah-Hartman

libata: add a host flag to ignore detected ATA devices

2012-06-17T18:21:29Z

commit db63a4c8115a0bb904496e1cdd3e7488e68b0d06 upstream. Where devices are visible via more than one host we sometimes wish to indicate that cirtain devices should be ignored on a specific host. Add a host flag indicating that this host wishes to ignore ATA specific devices. Signed-off-by: Andy Whitcroft Signed-off-by: Jeff Garzik Cc: Victor Miasnikov Signed-off-by: Greg Kroah-Hartman

Merge tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

2012-05-04T00:16:52Z

Pull libata fixes from Jeff Garzik: 1) Fix regression that could cause a misdiagnosis, which in turn could lead to an erroneous 3.0 Gbps -> 1.5 downshift, particularly when hotplug and suspend/resume is involved. 2) Fix a regression that led to ata%d controller ids being numbered one larger than in <= 3.4-rc3 (oh, the horror!). Controller ids should now be as expected. 3) add some DT, PCI id's 4) ata/pata_arasan_cf: minor cpp fixing/cleaning * tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: ata: ahci_platform: Add synopsys ahci controller in DT's compatible list ata/pata_arasan_cf: Move arasan_cf_pm_ops out of #ifdef, #endif macros libata: init ata_print_id to 0 ahci: Detect Marvell 88SE9172 SATA controller libata: skip old error history when counting probe trials

ata: ahci_platform: Add synopsys ahci controller in DT's compatible list

2012-05-03T18:08:53Z

SPEAr13xx series of SoCs contain Synopsys AHCI SATA Controller which shares ahci_platform driver with other controller versions. This patch updates DT compatible list for ahci_platform. It also updates and renames binding documentation to more generic name. Signed-off-by: Viresh Kumar Cc: Rob Herring Signed-off-by: Jeff Garzik