linux/drivers/acpi, branch v3.4.26

ACPI : do not use Lid and Sleep button for S5 wakeup

2013-01-17T16:50:53Z

commit b7e383046c2c7c13ad928cd7407eafff758ddd4b upstream. When system enters power off, the _PSW of Lid device is enabled. But this may cause the system to reboot instead of power off. A proper way to fix this is to always disable lid wakeup capability for S5. References: https://bugzilla.kernel.org/show_bug.cgi?id=35262 Signed-off-by: Zhang Rui Signed-off-by: Rafael J. Wysocki Cc: Joseph Salisbury Signed-off-by: Greg Kroah-Hartman

ACPI / scan: Do not use dummy HID for system bus ACPI nodes

2013-01-11T17:06:54Z

commit 4f5f64cf0cc916220aaa055992e31195470cfe37 upstream. At one point acpi_device_set_id() checks if acpi_device_hid(device) returns NULL, but that never happens, so system bus devices with an empty list of PNP IDs are given the dummy HID ("device") instead of the "system bus HID" ("LNXSYBUS"). Fix the code to use the right check. Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set

2013-01-11T17:06:54Z

commit 0ac1b1d7b7424cd6f129b5454b504b3cae746f0e upstream. The current acpisleep DMI checks only run when CONFIG_SUSPEND is set. And this may break hibernation on some platforms when CONFIG_SUSPEND is cleared. Move acpisleep DMI check into #ifdef CONFIG_ACPI_SLEEP instead. [rjw: Added acpi_sleep_dmi_check() and rebased on top of earlier patches adding entries to acpisleep_dmi_table[].] References: https://bugzilla.kernel.org/show_bug.cgi?id=45921 Signed-off-by: Zhang Rui Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

ACPI / video: ignore BIOS initial backlight value for HP Folio 13-2000

2012-12-17T18:37:46Z

commit 129ff8f8d58297b04f47b5d6fad81aa2d08404e1 upstream. Or else the laptop will boot with a dimmed screen. References: https://bugzilla.kernel.org/show_bug.cgi?id=51141 Tested-by: Stefan Nagy Signed-off-by: Zhang Rui Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

ACPI / PM: Add Sony Vaio VPCEB1S1E to nonvs blacklist.

2012-12-17T18:37:45Z

commit 876ab79055019e248508cfd0dee7caa3c0c831ed upstream. Sony Vaio VPCEB1S1E does not resume correctly without acpi_sleep=nonvs, so add it to the ACPI sleep blacklist. References: https://bugzilla.kernel.org/show_bug.cgi?id=48781 Reported-by: Sébastien Wilmet Signed-off-by: Lan Tianyu Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

ACPI / battery: Correct battery capacity values on Thinkpads

2012-12-17T18:37:45Z

commit 4000e626156935dfb626321ce09cae2c833eabbb upstream. Add a quirk to correctly report battery capacity on 2010 and 2011 Lenovo Thinkpad models. The affected models that I tested (x201, t410, t410s, and x220) exhibit a problem where, when battery capacity reporting unit is mAh, the values being reported are wrong. Pre-2010 and 2012 models appear to always report in mWh and are thus unaffected. Also, in mid-2012 Lenovo issued a BIOS update for the 2011 models that fixes the issue (tested on x220 with a post-1.29 BIOS). No such update is available for the 2010 models, so those still need this patch. Problem description: for some reason, the affected Thinkpads switch the reporting unit between mAh and mWh; generally, mAh is used when a laptop is plugged in and mWh when it's unplugged, although a suspend/resume or rmmod/modprobe is needed for the switch to take effect. The values reported in mAh are *always* wrong. This does not appear to be a kernel regression; I believe that the values were never reported correctly. I tested back to kernel 2.6.34, with multiple machines and BIOS versions. Simply plugging a laptop into mains before turning it on is enough to reproduce the problem. Here's a sample /proc/acpi/battery/BAT0/info from Thinkpad x220 (before a BIOS update) with a 4-cell battery: present: yes design capacity: 2886 mAh last full capacity: 2909 mAh battery technology: rechargeable design voltage: 14800 mV design capacity warning: 145 mAh design capacity low: 13 mAh cycle count: 0 capacity granularity 1: 1 mAh capacity granularity 2: 1 mAh model number: 42T4899 serial number: 21064 battery type: LION OEM info: SANYO Once the laptop switches the unit to mWh (unplug from mains, suspend, resume), the output changes to: present: yes design capacity: 28860 mWh last full capacity: 29090 mWh battery technology: rechargeable design voltage: 14800 mV design capacity warning: 1454 mWh design capacity low: 200 mWh cycle count: 0 capacity granularity 1: 1 mWh capacity granularity 2: 1 mWh model number: 42T4899 serial number: 21064 battery type: LION OEM info: SANYO Can you see how the values for "design capacity", etc., differ by a factor of 10 instead of 14.8 (the design voltage of this battery)? On the battery itself it says: 14.8V, 1.95Ah, 29Wh, so clearly the values reported in mWh are correct and the ones in mAh are not. My guess is that this problem has been around ever since those machines were released, but because the most common Thinkpad batteries are rated at 10.8V, the error (8%) is small enough that it simply hasn't been noticed or at least nobody could be bothered to look into it. My patch works around the problem by adjusting the incorrectly reported mAh values by "10000 / design_voltage". The patch also has code to figure out if it should be activated or not. It only activates on Lenovo Thinkpads, only when the unit is mAh, and, as an extra precaution, only when the battery capacity reported through ACPI does not match what is reported through DMI (I've never encountered a machine where the first two conditions would be true but the last would not, but better safe than sorry). I've been using this patch for close to a year on several systems without any problems. References: https://bugzilla.kernel.org/show_bug.cgi?id=41062 Acked-by: Henrique de Moraes Holschuh Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

ACPI: missing break

2012-12-10T18:59:40Z

commit 879dca019dc43a1622edca3e7dde644b14b5acc5 upstream. We handle NOTIFY_THROTTLING so don't then fall through to unsupported event. Signed-off-by: Alan Cox Signed-off-by: Rafael J. Wysocki Signed-off-by: Peter Huewe Signed-off-by: Greg Kroah-Hartman

ACPI video: Ignore errors after _DOD evaluation.

2012-11-26T19:38:44Z

commit fba4e087361605d1eed63343bb08811f097c83ee upstream. There are systems where video module known to work fine regardless of broken _DOD and ignoring returned value here doesn't cause any issues later. This should fix brightness controls on some laptops. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47861 Signed-off-by: Igor Murzov Reviewed-by: Sergey V Signed-off-by: Zhang Rui Signed-off-by: Abdallah Chatila

ACPI: EC: Add a quirk for CLEVO M720T/M730T laptop

2012-10-21T16:27:57Z

commit 67bfa9b60bd689601554526d144b21d529f78a09 upstream. By enlarging the GPE storm threshold back to 20, that laptop's EC works fine with interrupt mode instead of polling mode. https://bugzilla.kernel.org/show_bug.cgi?id=45151 Reported-and-Tested-by: Francesco Signed-off-by: Feng Tang Signed-off-by: Len Brown Signed-off-by: Greg Kroah-Hartman

ACPI: EC: Make the GPE storm threshold a module parameter

2012-10-21T16:27:57Z

commit a520d52e99b14ba7db135e916348f12f2a6e09be upstream. The Linux EC driver includes a mechanism to detect GPE storms, and switch from interrupt-mode to polling mode. However, polling mode sometimes doesn't work, so the workaround is problematic. Also, different systems seem to need the threshold for detecting the GPE storm at different levels. ACPI_EC_STORM_THRESHOLD was initially 20 when it's created, and was changed to 8 in 2.6.28 commit 06cf7d3c7 "ACPI: EC: lower interrupt storm threshold" to fix kernel bug 11892 by forcing the laptop in that bug to work in polling mode. However in bug 45151, it works fine in interrupt mode if we lift the threshold back to 20. This patch makes the threshold a module parameter so that user has a flexible option to debug/workaround this issue. The default is unchanged. This is also a preparation patch to fix specific systems: https://bugzilla.kernel.org/show_bug.cgi?id=45151 Signed-off-by: Feng Tang Signed-off-by: Len Brown Signed-off-by: Greg Kroah-Hartman